|
Tankless
Water Heaters
Enjoy
an Unlimited Supply of Hot Water!
Save Money and Save Water!
Electric
- Whole House - Large
|
Product ID: SBE-DHC-E30
|
Saves energy and reduces
your electric bill with a saving of 15 - 20%
For Use In Homes,
Apartments, Condos with 3-4 people
|
|
Featuring Advanced Microprocessor Control
-
The electronic control system in the DHC-E does not
allow the water temperature to go above 125°F (52°C), which
eliminates the possibility that scalding may occur. On the other hand,
125°F (52°C) water is sufficiently hot for most uses.
-
Controls the temperature of the outgoing water plus or
minus approximately 1/2 of 1 degree vs. the conventional tank hot
water heaters that are plus or minus 6-10 degrees.
-
Controls the amount of the power used to achieve the
temperature dependant on demand.
|
-
Conductors should be sized
to maintain a voltage drop of less than 3% under load
-
Rugged all copper design
ensures many years of reliable service
-
Equipped with a safety
high-limit with manual reset
-
Completely replaces a conventional
tank heater
-
Takes up less space than the
conventional tank type water
-
No disruption to your
comfort and hot water needs
-
Keeps heating water
instantly as you require
-
Tankless water heaters are
considered a non-continuous load
Take Off The Cover
And Have A Look!
As an International leader in the tankless
electric water heating industry, STIEBEL ELTRON is proud to have pioneered
this technology. The company's engineering and manufacturing tradition of
excellence means that you can depend on its performance for many years to
come.
DHC-E-30 Technical Data
| Data |
DHC-E-30
|
| Phase |
1
|
| Voltage V |
208 |
240 |
| Wattage
KW |
21.6 |
58.8 |
| Amperage
AMP |
105 |
120 |
| Min. Required circuit
breaker
A |
3 x 40 |
3 x 50 |
| Recommend
wire size AWG Copper |
3
x 8 |
3
x 8 |
Max. temp. increase
above ambient water temperature
@2.25 GPM |
65 |
87 |
|
@3.00 GPM |
49 |
65 |
|
@4.50 GPM |
33 |
44 |
| Min.
water flow to activate unit GPM/lmln |
0.87/3.3 |
| Weight
Lb/kg |
24.25/11 |
| Normal
water volume
Gal |
0.39/1.5 |
| Height inch/cm |
14
1/2 (36.7) |
| Width inch/cm |
21
3/4 (55.2) |
| Depth inch/cm |
4
5/8 (11.6) |
| Working
pressure
PSI/BAR |
150/10 |
| Tested to pressure
PSI/BAR |
300/20 |
| Water
connections |
3/4"
NPT |
Descriptions to
the above data:
-
Phase: All households in the US
are single phase.
-
Voltage: 208
is for commercial and 240 is for residential.
-
The wattage:
measured in kilowatt hours.
-
Amperage:
Is incoming service to your home or business that you will need to
operate this unit.
-
Circuit Breaker: The size of
breaker that is needed.
-
Recommended
wire size is: (AWG Copper) This means American
Wire Gage for Copper wire. It is how big the wire measures
around. The smaller the number, the bigger the
wire.
-
If you set the
flow rate to be 2.25 gallons per minute, the temperature of
the hot water coming out of the tap will be 87 degrees higher
(residential) than the ambient temperature coming into your
house. So if the temperature of the water coming into
your home is 50 degrees, then the hot water coming from your
tap will be 137 degrees.
-
Minimum water flow
to activate the unit to make hot water.
-
The dimensions on
these units are considerably smaller than the conventional
tank hot water heaters.
-
Weight is
the weight of the unit as it is empty.
-
Maximum
operating pressure is the amount of pressure the unit will
work at. (PSI - Pounds per square inch). Homes in
the city run on 80 psi and in the rural area homes run on
40-60 psi.
-
Testing to
pressure prevents the unit from bursting, causing accidents,
burns, etc.
-
Water connection
is 3/4"
|
Parts
For Easier Installation
Saving time during installation is a large factor. No one likes making
all those trips to the hardware store. Make sure to check out this page
before completing your order.
Click here for Flex Connectors
|
Order one Today!
Price:
$650.00
ATTENTION:
The voltage, amperage, and circuit breaker specifications must
be met for this heater to function. Please make sure all
requirements are met before purchasing this heater. If you have
any questions about these requirements, please call 406-889-5288.
|
|
